06-18-2007, 06:25 PM
[cool][#0000ff]THE ROJO TWINS (H3 Freestyles) ARE HERE. We had two boxes waiting for us when we returned from Willard Bay last Friday. I spent several hours over the weekend sniffing PVC cement and tinkering with the new setups. [/#0000ff]
[#0000ff][/#0000ff]
[#0000ff]We will be taking the new craft out for their maiden voyages on Jordanelle tomorrow morning, and will have a ride report after that trip. In the meantime, here are some pics to give you an idea of how I spent my weekend.[/#0000ff]
![[Image: gforum.cgi?do=post_attachment;postatt_id=26569;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26569;)
Initial setup on tables. Haven't decided on what kind of apron to use yet. Probably just a larger rigid plastic.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26570;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26570;)
Side view after setting up new Utility rack.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26571;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26571;)
Left side setup, with sonar and rod rack...unpainted.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26572;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26572;)
Connection to transducer shaft is left unglued, to allow free swivel action up and down...to prevent damage to transducer during launching and beaching.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26573;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26573;)
Battery and spared transducer cable is stored in the small rear pocket. The cable to the display runs forward through the 1/2" PVC beside the pocket. The fittings are screwed to 2"X2" wood blocks inside the pockets and the connections are not glued.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26574;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26574;)
This is one of my new ideas...the "PVC ram mount" installed on the 2" wood support block inside the pocket...and the sonar display easily set up and removed.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26575;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26575;)
The display easily disconnects from the ram mount, and stores in the spacious pockets for transport.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26576;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26576;)
This shows the wood support block, with the PVC goodies as they attach once the block is secured inside the pockets.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26577;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26577;)
Rod rack, painted with Rustoleum Plastic Paint. Sprayed on quickly and easily and dried fairly fast. Will watch over time to see how it holds up.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26578;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26578;)
Red painted rod holder installed on tube. Stabilized with bungee cords attached to D rings under the tube.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26579;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26579;)
Another of my newest ideas...a multipurpose tool/utility rack. Serves to hold the rod you are actively using...while handling fish or rerigging...and holds both tools and net. Double secured to D rings with bungee cord and S clips.
![[Image: gforum.cgi?do=post_attachment;postatt_id=26580;]](http://www.bigfishtackle.com/cgi-bin/gforum/gforum.cgi?do=post_attachment;postatt_id=26580;)
Ready to load up in the vehicle for the trip to the water. By partially deflating, the front elongated air bladder extensions can be folded up over the front for easier transporting. In this picture, you may be able to see that the bungees attached to the back D rings have been run through the D rings on the front of each air chamber, and then attached to the D ring "kitty corner" across in front. Very secure and compact for transport.
[#0000ff]I have taken lots more pictures and will be able to provide some step by step stuff for anyone wanting to incorporate any of these ideas.[/#0000ff]
[signature]
[#0000ff][/#0000ff]
[#0000ff]We will be taking the new craft out for their maiden voyages on Jordanelle tomorrow morning, and will have a ride report after that trip. In the meantime, here are some pics to give you an idea of how I spent my weekend.[/#0000ff]
Initial setup on tables. Haven't decided on what kind of apron to use yet. Probably just a larger rigid plastic.
Side view after setting up new Utility rack.
Left side setup, with sonar and rod rack...unpainted.
Connection to transducer shaft is left unglued, to allow free swivel action up and down...to prevent damage to transducer during launching and beaching.
Battery and spared transducer cable is stored in the small rear pocket. The cable to the display runs forward through the 1/2" PVC beside the pocket. The fittings are screwed to 2"X2" wood blocks inside the pockets and the connections are not glued.
This is one of my new ideas...the "PVC ram mount" installed on the 2" wood support block inside the pocket...and the sonar display easily set up and removed.
The display easily disconnects from the ram mount, and stores in the spacious pockets for transport.
This shows the wood support block, with the PVC goodies as they attach once the block is secured inside the pockets.
Rod rack, painted with Rustoleum Plastic Paint. Sprayed on quickly and easily and dried fairly fast. Will watch over time to see how it holds up.
Red painted rod holder installed on tube. Stabilized with bungee cords attached to D rings under the tube.
Another of my newest ideas...a multipurpose tool/utility rack. Serves to hold the rod you are actively using...while handling fish or rerigging...and holds both tools and net. Double secured to D rings with bungee cord and S clips.
Ready to load up in the vehicle for the trip to the water. By partially deflating, the front elongated air bladder extensions can be folded up over the front for easier transporting. In this picture, you may be able to see that the bungees attached to the back D rings have been run through the D rings on the front of each air chamber, and then attached to the D ring "kitty corner" across in front. Very secure and compact for transport.
[#0000ff]I have taken lots more pictures and will be able to provide some step by step stuff for anyone wanting to incorporate any of these ideas.[/#0000ff]
[signature]